This SmallRig 2916 side handle review looks at a lightweight cage grip for mirrorless and other small-camera rigs. Its appeal is straightforward: an adjustable handhold that attaches to compatible cages and adds a cold shoe and strap eyelet.
SmallRig 2916 Handle Review Summary
The quick verdict

2,000+ ratings
Read Amazon ReviewsSmallRig 2916 Mini Side Handle
A compact cage-mounted grip for filmmakers who want adjustable left- or right-hand positioning and accessory mounting points.
- Uses two 1/4-inch-20 screws to attach to cage holes spaced 18 mm apart.
- Slides up and down for positioning along the cage.
- Can be reoriented for left- or right-hand use with the built-in wrench.
- Includes a cold shoe for compatible accessories such as a flash or microphone.
Pros
- Low weight suits small-camera cages and compact handheld rigs.
- Adjustable height helps accommodate different cage layouts.
Consider before buying
- Requires two cage mounting holes with the specified 18 mm spacing, so compatibility needs checking before purchase.
- Its mini-grip form may feel too small for buyers who prefer a larger handle.
Read the full review summary
The 2916 is a compact side grip built around two 1/4-inch-20 screws, with an 18 mm spacing requirement for the cage’s threaded holes.
Its up-and-down adjustment and reversible orientation give you options for fitting the handle to different cage heights and switching sides, while a built-in wrench supports those changes.
At 139 g, it is suited to compact camera builds where adding a grip should not make the rig much bulkier.
The cold shoe and eyelet provide useful places to attach compatible accessories, but the handle is a small grip rather than a full-size support.
Buyers should check cage compatibility and keep the assembled load within its 3.5 kg maximum bearing capacity.
The buying factors
SmallRig 2916 Handle Scorecard
Editorial scores reflect listed features and buyer fit; they are not laboratory measurements or customer ratings.
Cage compatibility clarity
The mounting pattern is specific: two 1/4-inch-20 threaded holes spaced 18 mm apart.
Positioning flexibility
The handle slides up and down, and its connection can be changed to switch the grip between sides.
Handedness options
Its reversible orientation supports left- or right-hand use.
Accessory expansion
A cold shoe and eyelet offer straightforward attachment points for compatible accessories and a wrist strap.
Portability
The stated 139 g weight fits a compact rig setup.
Load headroom
The maximum bearing capacity is 3.5 kg, so buyers need to account for the complete mounted setup.
Key Features and Specifications of SmallRig 2916 Handle
- Uses two 1/4-inch-20 screws to attach to cage holes spaced 18 mm apart.
- Slides up and down for positioning along the cage.
- Can be reoriented for left- or right-hand use with the built-in wrench.
- Includes a cold shoe for compatible accessories such as a flash or microphone.
- Has an eyelet for attaching a compatible wrist strap.
- Combines aluminum alloy and PC+ABS plastic and weighs 139 g.
- Maximum bearing capacity is 3.5 kg.
Pros and Cons of SmallRig 2916 Handle
Pros
- Low weight suits small-camera cages and compact handheld rigs.
- Adjustable height helps accommodate different cage layouts.
- Can be configured for either hand and moved to the other side of a cage.
- Cold shoe and strap eyelet add useful mounting options without requiring a separate extension.
Consider before buying
- Requires two cage mounting holes with the specified 18 mm spacing, so compatibility needs checking before purchase.
- Its mini-grip form may feel too small for buyers who prefer a larger handle.
- The 3.5 kg maximum bearing capacity calls for attention to the weight of the complete setup.
Who Should Buy SmallRig 2916 Handle?
Good fit
Consider the 2916 if you use a mirrorless or small-camera cage with the matching threaded-hole layout and want a compact side grip.
Its sliding adjustment and reversible mounting are useful when the same rig needs to suit different operators or shooting positions.
It also makes sense if you want a simple place to attach a compatible flash or microphone, with an eyelet available for a wrist strap.
Before ordering, verify the cage’s hole spacing, think about which side you will grip, and check the total supported load.
Who should skip it
Skip this handle if your cage does not have two 1/4-inch-20 threaded holes spaced 18 mm apart, or if you need a larger handhold.
A larger grip may better suit that preference; confirm the handle dimensions and ergonomics against your own setup before choosing.
Look elsewhere if your rig’s mounted load exceeds the 3.5 kg maximum bearing capacity. Keep the full combination of camera and attached equipment within that limit.
How the SmallRig 2916 Handle Fits a Compact Rig
Check the cage mounting pattern
The handle’s two-screw connection depends on a precise cage layout: two 1/4-inch-20 threaded holes spaced 18 mm apart.
Compare that spacing on the intended side of your cage before buying, and check that the chosen position leaves the grip where you can comfortably reach it.
Use the adjustment to set your grip
The handle slides up and down, and the connection can be reoriented for left- or right-hand use. That gives you room to adapt the grip position to the cage and operator.
The built-in wrench is intended for switching the orientation; allow time to make and secure that change before shooting.
Keep the rig within the load limit
The 3.5 kg maximum bearing capacity is a key constraint when building out a camera rig.
Consider the combined weight of the camera and attached gear supported by the handle, rather than treating the grip as suitable for any cage configuration.
Add accessories without enlarging the grip
The cold shoe provides a mounting point for compatible accessories such as a flash or microphone, while the eyelet accepts a compatible wrist strap.
These additions can make the handle more useful within a compact setup; check the size and placement of any accessory against the space around your cage.
Alternatives to SmallRig 2916 Handle
Camera Mounts & Clamps alternative

1,000+ ratings
Read Amazon ReviewsSmallRig 3766 Lightweight NATO Top Handle
Choose the 2916 when you specifically want a side grip and your cage has the matching screw pattern.
Consider the 3766 if a top handle better suits your shooting position and your cage has a NATO rail; that rail is required and sold separately.
- The 3766 is a top handle for cages with a NATO rail.
- It weighs 124 g and has five cold shoe mounts, ten 1/4-inch threaded holes and two 3/8-inch threaded holes; its stated supported weight is up to 10 kg.
- The 2916 is a side grip that attaches with two 1/4-inch-20 screws at 18 mm spacing and weighs 139 g.
Camera Mounts & Clamps alternative

800+ ratings
Read Amazon ReviewsSmallRig 4336 Sony A6700 Cage Kit
Choose the 2916 if you already have a compatible cage and only need a side handle.
The 4336 is the more relevant option when you need a cage specifically for the Sony A6700, with its included HDMI clamp and mounting features; it is a different starting point for a rig rather than a substitute grip.
- The 4336 is a cage kit made for the Sony A6700.
- It includes an HDMI cable clamp, has 1/4-inch-20 and 3/8-inch-16 mounting holes, and an integrated Arca-Swiss quick-release plate.
- The 2916 is a standalone side grip for cages with two 1/4-inch-20 threaded holes spaced 18 mm apart.
Is SmallRig 2916 Handle Worth It?
The SmallRig 2916 Mini Side Handle is worth considering for a compact camera cage when its two-hole mounting pattern matches and a lightweight, adjustable side grip fits your shooting style.
Its reversible orientation, sliding position, cold shoe and strap eyelet give it useful flexibility for a small rig.
Check the cage spacing and the full supported load before buying, and keep in mind that this is a mini grip.
If those constraints fit your setup, it is a practical way to add a dedicated handhold without moving to a larger handle.
Your review at a glance

2,000+ ratings
Read Amazon ReviewsSmallRig 2916 Mini Side Handle
A compact cage-mounted grip for filmmakers who want adjustable left- or right-hand positioning and accessory mounting points.
- Uses two 1/4-inch-20 screws to attach to cage holes spaced 18 mm apart.
- Slides up and down for positioning along the cage.
- Can be reoriented for left- or right-hand use with the built-in wrench.
- Includes a cold shoe for compatible accessories such as a flash or microphone.